Product outline

  • Variations of torque, rpm, and power can be monitored and saved on PC.
  • Maximum, minimum, and average value can be displayed.
  • Measurement (numeric) data is automatically saved in CSV format.
  • The unit supplies operation power to UTMⅡ/UTMV.
  • Two cables are attached: one for UTMⅡ/UTMV and the other for PC.
Application software for USB interface

・ Display real-time data sent from UTMⅡ/UTMV via USB0.
・ Torque, rotation speed, power and time in the graph can be specified by cross-lines.
・ Measurement(numeric) data is automatically saved in CSV format.
・ Easy calibration with simple selection of sensor types and display conditions!


■ Display mode
[Normal]
In-progress waveform data will be displayed.
Maximum, minimum, and average value of the waveform data will be displayed.

1. Single
After “start” button is pressed, data will be recorded once for pre-set time period.

2. Continuous
“Single” mode operation will be repeated in cycle until “stop” button is pressed.

3. Level trigger
After “start” button is pressed, it will be put on standby for a trigger.It starts to import the data when the input level goes over the trigger level.

[History]
Previous waveform data can be displayed (up to 1000 files of waveform data can be saved).

■ Trigger options
・Pre-trigger ・Level trigger data ・Trigger level
・Trigger slope ・Repeating trigger

■ Cursors (max.: two)
Torque readings at cursor positions and difference between those two readings will be displayed.

Example of use



* PC and special software are required to use the TM201.
Application software for the USB interface option can be downloaded from this page.

Specifications

Torque sensor input (voltage input)
Signal input range -5 to +5 V Input impedance : 1 MΩ or more
Accuracy Non-linearity : Within 0.02% FS±1 digit
Zero drift : Within 0.2 mV/℃ RTI
Gain drift : Within 0.01%/℃
Analog filter Primary low-pass filter 1 kHz (fixed)
Digital filter Secondary low-pass filter fc = 3 Hz, 30 Hz, 300 Hz, OFF (variable)
Data output rate 300 times/sec.
Resolution : 24 bit (binary) Approx. 1/30000 with respect to 5 V
 
Pulse input for rpm (input for open collector type)
Maximum input frequency Compatible with the pulse output frequency of UTMⅡ/UTMV series
Minimum input frequency Select from 15, 10, 5, 3, or 2 rpm (when pulse rate is 4 ppr)
Select from 60, 40, 20, 12, 8 rpm (when pulse rate is 1 ppr)
Minimum pulse width 50 μs
Circuit layout No-voltage (dry) contact input (minus common):
open collector outputs can be connected (Ic = approx. 10 mA)
 
Power supply for UTMⅡ/UTMV
Power supply DC 24 V (UTMⅡ/UTMV 1 unit)
 
Display section
LED status light LED (Red) : power supply/alarm status
LED (Green) : UTMⅡ/UTMV is operating normally
 
Interface
Interface USB
 
General specifications
Power supply AC 100 V to 240 V (+10%-15%) (free power source 50/60 Hz)
* When supplied AC adapter is used.
Power consumption 4 W typ. (AC adapter)
Operating Operation : 0℃ to +40℃ Storage : -10℃ to +60℃
Humidity : 80% RH or less (non-condensing)
Dimensions 50(W) × 23(H) × 80(D) mm (Not including projections)
Weight Approx. 120 g
CE marking certification EMC directives EN61326-1
Safety standard EN62311
Please specify requirement for CE marking certified product when making your order.
 
Attachments
Setup guide 1
AC adapter for TM201 1.8 m 1
Cable for UTMⅡ/UTMV connection 2 m 1
MiniUSB -USB cable 1.8 m 1
 

Optional accessories

Model Description
CA81-USB miniUSB-computer USB cable 1.8 m
(same as attachment)
CATM21-M Cable for connecting UTMⅡ/UTMV 2 m
(same as attachment)
CATM51-M Cable for connecting UTMⅡ/UTMV 5 m
CN90 Waterproof plastic connector for UTMⅡ/UTMV
TM201 AC PIN EU Switching AC PIN(EU)
 



Please note that there are possibilities of individual differences in a color tone on display devices such as LEDs, fluorescent display tubes and LCDs due to manufacturing process or production lots.



Download

Product catalogue(PDF)
⇒Download Page
Operation manual(PDF)
External dimension
DXF
(ZIP)
PDF
Support tools
Software